Paving method: In the fall, the weather is getting colder and the air is getting drier. There are three things to note when installing solid wood flooring: First, it is forbidden to sprinkle water on the ground within ten days before the installation of solid wood composite flooring. Second, after the cement mortar flattened the ground, install it after 30 days under ventilation. This is to ensure that the floor humidity meets the requirements for installing the floor. At the same time, the moisture content of the floor will decrease as the moisture content in the air drops. Thirdly, in the process of decreasing the moisture content of the floor, the floor will shrink naturally due to the loss of moisture from the wood fiber. Therefore, the physical phenomenon of the wet swell and shrinkage of the floor is unavoidable. If the water content is too low, it will directly cause cracks in the floor. . Humidifiers, slightly damp mops, etc. can be used to properly humidify the interior to reduce the loss rate of the floor moisture content. The specific method of paving is: adjusting the orientation of the floor, extending from the beginning of the door to the room, the maximum span of the floor is 6m × 8m, beyond which a contraction joint must be left and the buckle be applied; the root of the door and the interface of the door bead Reserve expansion joints to be greater than 8 mm; splicing request continuous, uniform, residual glue should be cleared in time; baseboard must reach 12 mm thick, otherwise it is difficult to cover up the contraction joint; aluminum alloy bead thickness should be guaranteed in more than 2 mm, Too thin and easy to warp and deform. In addition, after the stay, the floor is best to be raised once a month, not only to extend the life of the floor application, but also to prevent moisture in the air from penetrating into the substrate, resulting in deformation of the floor. In addition, the weather in the north has more wind and sand in the autumn, and the floor needs frequent dust removal. Usually, dust can be removed with a broom or a vacuum cleaner. The places that are frequently stamped on the floor must be vacuumed. Pay special attention to the hallway and the walkway leading to the outside. To prevent dust from entering the house, place dust-proof pads in the entry area. Maintenance: First, keep the indoor ventilation and dry environment Maintaining indoor ventilation regularly can not only make the chemical substances in the composite wood floor volatilize as much as possible, but also discharge it to the outside, and can also exchange damp indoor air with the outside. Especially in the absence of people living and maintaining for a long time, indoor ventilation is more important. Common practice is: often open the window or door, but do not allow air convection, air conditioning system and ventilation system can be used to create a dry and clean indoor environment. Second, avoid sun exposure and rain wet In some houses, sunlight or rain can enter the interior of the room directly from the windows. This will cause harm to the multi-layer parquet. Sunlight will accelerate the aging of paint and glue, and it will also cause shrinkage and cracking of solid wood flooring. After the rain is wet, the moisture absorbed by the multi-layer solid wood floor will cause swelling and deformation, and it will also make the multilayer solid wood composite floor moldy. Therefore, special attention must be paid to daily use. Third, keep the relative humidity suitable Generally should be the best at 45% to 75%. Fourth, to avoid damage to the composite wood floor surface The veneer of the multi-layer solid wood composite floor is not only the decorative layer of the floor but also the protective layer of the floor. Therefore, the impact of hard objects, scratches of sharp tools, and friction of metal should be avoided. Chemicals cannot be stored indoors. In addition, the interior furniture should be transported with care, and the feet of the furniture should be placed with rubber. In public places, carpets should be laid on the main passages. It is advisable to place foot pads at the entrance of the hall to reduce the carry-over of dirt or mud. Fifth, the correct cleaning and care During daily use, the floor should be cleaned regularly to keep the floor clean and sanitary. When cleaning, clean the dust and debris with a clean broom and wipe it manually with a wringer. If the area is too large, clean the cloth mop and hang it to dry. Drag the ground. Do not wash with water or clean it with a damp rag or mop. Normally, if there is spilled water on the ground, it should be immediately wiped dry with a dry rag. If conditions allow, floor waxes can also be applied at intervals to enhance the protection of composite wood floors. If the paint surface is damaged, you can use ordinary varnish to make it up or ask the manufacturer to repair it. Sixth, avoid floor invasion Never touch or soak composite wood floors with large volumes of water, and do not use corrosive objects to wipe laminate flooring. Seven, to avoid damage to the floor When moving the furniture, it cannot be pushed and pulled on the composite wood floor. It should be lifted up flat. If necessary, it should be covered with a rubber pad under the furniture or at the corners to avoid damage to the composite wood floor. Eight, common stain treatment methods Chocolates, oils, juices, wines, and wines can be cleaned with lukewarm water and neutral detergents; inks, lipsticks, minerals, shoe polish, and nail polishes can be cleaned with alcohol, but should be removed in time to prevent corrosion of laminate flooring. Related Reading: "National Standard for Solid Wood Flooring" Http:// Offest Printing Graphic Film,Thermal Ctp Printing Plate,Film Thermal Ctp Plate,Aluminum Printing Plate SUZHOU HUAGUANGBAOLI PRINTING PLATE CO.,LTD , https://www.huabaoiguang.com
Autumn solid wood flooring installation and maintenance methods