Seven points for improvement of plexiglass screen printing process

[Review]: Plexiglass screen printing: the best choice for low cost and high return

【Extended】 : Analysis of the main points of plexiglass screen printing ink

【Extended】 : Introduction of DBL glass screen printing ink

[Extended]: Analysis of the photo-engraving process of plexiglass screen printing

Now the application range of products processed with plexiglass is getting wider and wider, and the requirements for plexiglass processing are getting higher and higher, especially plexiglass screen printing, which is a challenge and an opportunity for plexiglass processing manufacturers. Mastering high-quality plexiglass screen printing technology is the top priority of plexiglass processing plants. The main points for improving the plexiglass screen printing process are the following 7 points:

1. A basic requirement for perfect image reproduction is that the quality of the transparent positive film is better, that is, the edges of the dots should be neat and opaque. The color separation film and the printing ink used use the same color scale.

2. The positive film is placed on the glass plate, and then exposed, and the stretched screen is placed on the positive film and parallel to the image axis. If moire appears, rotate the screen to the left or right until the moire disappears, usually by 7 °. The area where moire is easy to form is located in the direction of the wire mesh and at the intersection of the wire mesh. The main color and the darker color cause more problems with moire.

3. For four-color printing, aluminum screen frames of the same size and stability should be used, and the screen frames used are all stretched with the same type and type of screen. The use of dyed silk screen helps to eliminate moire. The tension of the screen should be uniform and the tension of the four screen printed four screens should be the same.

4. The ground squeegee blade is essential for high-quality printing. The Shore hardness of the blade is about 70. The squeegee should be set at an angle of 75 °. If the angle of the squeegee is adjusted too flat, the printed image may be blurred. If the angle is adjusted too steep, the risk of screen printing image distortion is greater.

5. The ink return knife should not be installed too low. If so, the film plate will be filled with excessive ink, and the printed matter is easy to blur and smudge.

6. The mesh tone image is printed with high-viscosity ink. The finer the screen, the darker the ink.

7. When using UV ink, the tone range of the mesh tone image should be selected from 5% to 80%, and the Shore hardness of the rubber scraper should be 75. In order to control the UV ink from overprinting in color, it is recommended to print in the order of cyan, magenta, yellow, and black. When using UV ink, the screen thickness should not exceed 5um.

Hexagon Silicone Teething Beads

we had 2 different size of hexagon Silicone Teething Beads,14mm and 17mm. most customer like to use hexagon silicone teething beads to make different hexagon Teething Necklace design such as 5pcs hexagon teething necklace or 3pcs hexagon or 2pcs round beads  necklace design. the popular color in hexagon silicone teething beads are marble,mint and white.it can be strung a short Baby Teething Necklace.


Please notice that if the hexagons silicone teething beads was damaged, discard immediately as this may become a potential choking hazard. Children with fully developed teeth may be able to chew or tear beads.


Attention:Please don't leave your child or babies unattened with this toy.


Silicont teething beads

Silicone beads


For more: Silicone teething beads, Silicone baby teether, silicone Baby Pacifier Clips , Baby Teething Mitten, baby teething necklace.


Hexagon Silicone Teething Beads

Hexagon Silicone Teething Beads,Hexagon Silicone Beads,Loose Hexagon Silicone Beads,Hexagon Teething Beads

Shenzhen Kean Silicone Product Co., Ltd. , https://www.keansilicon.com