The viscosity of the upper glass liquid is different from the viscosity of the glass near the bottom of the crucible. Pay special attention when picking up the material. Therefore, luck is at ease, and the blowing power is just right to ensure the size of the product. After the knife is fed, try to shake the drill. The feed speed should not be too fast. Add some water to the drill hole. Basic curing in 4 hours. Then make silicone structural adhesive; Frame decoration: Generally, the frame of the glass frame without the mullion is embedded in the veneer of the wall, cylinder and ground. Make sure the scratch line leaves approximately 15 cm of edges on both sides to allow for a grip. Lubrication performance, cooling performance, rust resistance, cleaning performance - four can be integrated. The so-called blow-blowing method of blowing into a preliminary type and then blowing into a product is suitable for making small mouth vessels and bottles. Sort round bottles by bottle geometry. When there is a crack in the entire circumference. Put in water. All the same glass walls are installed and leveled. 1 Apply a slight force to your wrist and smash the glass in half along the line. During printing, the ink is transferred to the substrate through the mesh of the graphic portion by the extrusion of the squeegee to form the same graphic as the original. It can also be blown freely without mold, and then knocked off from the blowpipe. Remove the dirt from the car glass before the car glass is repaired. After passing through the oven, the ink will dry out and the pattern will not be easily erased. (For example, some optical instruments) are usually stuck on a special grinding machine with copper tubing. And baked at high temperature. The principle is mainly to transform the downward force of the wedge into the force level of the object. A number of staggered tool marks are randomly cut in the horizontal and vertical directions in the disc. The section is elliptical, although the capacity is small, but the shape is unique, and users also like it. However, the color is limited. What are the characteristics of the mobile glass polishing liquid? Excellent lubrication performance, anti-wear performance, improved processing accuracy, surface finish, effectively protect the tool and extend the service life of the tool. The practical technique of hand-blown glass should be uniform. The symmetrical distribution of the hot glass in each part mainly depends on whether the rotating speed of the blown iron pipe is proper. If the rotating speed is too fast or too slow, the thickness of the product will be uneven. The gradual color process is generally used in magnetron sputtering coating equipment. At present, Huawei, Lenovo and other mobile phone gradient color shells use PVD vacuum gradient coating process. After finishing the line, there is no success. Put the glass knife under the glass and the glass on the table. The knife is also placed under the glass on the table. Facing the scratch marks, bring the gloves, pay attention to safety, and the palms of the two hands are separated. Hold the traces on both sides, the average position of the edge of the glass, both hands and palms at the same time force, be quick, fast, do not slowly force, hear, slam, immediately force, prevent the separate glass from pressing hard on the table Causes rupture. The screen printing equipment of the mobile phone casing spraying line generally uses the silk screen printing process for the monochrome gradient. The screen printing machine is a machine for printing with the screen printing plate, which belongs to the printing machine. After the repair, the effect is very good, but after a while, the crack seems to appear again: the common reason is overheating. It is a suitable temperature to heat the glass to 26--32 °C. After this temperature, the glass will expand and the resin will be Extrusion, so it seems to have been repaired at the time, in fact, some of the resin in the crack has overflowed, and the crack will appear again when the glass cools down. You can mark the glass with a marker (if you want to cut a straight line, you can use a ruler). During mechanical blowing, the molten glass flows out from the outlet of the glass melting furnace, and a gob of a set weight and shape is formed by the Feeder, cut into a preliminary mold, blown or pressed into a preliminary shape, and then transferred into a molding die to be blown. product. It is a glass bottle with an inner diameter of less than 20mm, which is used for packaging liquid materials such as soda, beer and so on. Anodizing equipment line body: manual line, semi-automatic line, fully automatic line, selected by product weight, length and output. Scratches above 60 cm increase the risk of glass breakage. Then: Use a bowl of the desired diameter and snap it onto the glass. How to open a round hole in the window glass first. Gently tap the back of the scratch with a chisel. 1 Grasp the ends of the glass dividing line with your hand. Canned bottles. Article source address: http:// Cat Water Fountain,Elevated Dog Bowls,Ceramic Dog Bowls,Stainless Steel Dog Bowls NINGBO BRIGHT MAX CO., LTD. , https://www.smartrider-horserugs.com
Principle of working principle of transmission automatic screen printing machine